Onboard Decision-Making for Nominal and Contingency sUAS Flight

This study presents an onboard decision-making architecture for small unmanned aerial systems (sUAS). The decision-maker is part of NASA's SAFE50 project that is working under the UAS Traffic Management (UTM) Technical Capability Level (TCL) 4 to provide autonomous point-to-point UAV flight in BVLOS, high-density urban environments. The decision-maker monitors various metrics to determine the safety and feasibility of the mission and categorizes flight states as Nominal, Off-Nominal, Alternate Land, and Land Now in a finite state machine. Changes in the monitored metrics serve as transitions in the state machine and trigger replanning. Navigation degradation and communication failure are simulated to show the feasibility of the decision-maker framework in appropriately switching the flight state

Vehicle to Vehicle (V2V) Communication for Collision Avoidance for Multi-Copters Flying in UTM -TCL4

NASAs UAS Traffic management (UTM) research initiative is aimed at identifying requirements for safe autonomous operations of UAS operating in dense urban environments. For complete autonomous operations vehicle to vehicle (V2V) communications has been identified as an essential tool. In this paper we simulate a complete urban operations in an high fidelity simulation environment. We design a V2V communication protocol and all the vehicles participating communicate over this system. We show how V2V communication can be used for finding feasible, collision-free paths for multi agent systems. Different collision avoidance schemes are explored and an end to end simulation study shows the use of V2V communication for UTM TCL4 deployment

Coordinated Turn Trajectory Generation and Tracking Control for Multi-Rotors Operating in Urban Environment

The paper presents an efficient trajectory generation and tracking approach for multi-rotor air vehicles operating in urban environment, which takes into account uncertainties in the urban wind field and in the vehicle's parameters. Generated trajectories are sufficiently smooth, based on the differential flatness of the vehicle's dynamics and optimal in the sense of minimum agility and time. They pass through given set of way points, guarantee flight without a side-slip, and satisfy vehicle's dynamics and actuators constraints. In addition, an algorithm is presented to compute the required power to traverse the generated trajectory. Presented algorithms are implementable in real time using on-board computers. They do not take into account the vehicle's existing flight controller, hence there is no guarantee that the controller will be able to provide acceptable tracking of the generated trajectory, especially in the presence of atmospheric disturbances. To this end, we propose an adaptive augmentation algorithm to improve vehicle's performance by taking into account the effects of disturbances and on-line estimates of vehicle's existing flight controller's gains. The algorithms have been verified by simulations using DJI S1000 octocopter's model

Coordinated Turn Trajectory Generation and Tracking Control for Multi-rotors Operating in Urban Environment

The paper presents an efficient trajectory generation and tracking approach for multi-rotor air vehicles operating in urban environment, which takes into account uncertainties in the urban wind field and in the vehicle's parameters. Generated trajectories are sufficiently smooth, based on the differential flatness of the vehicle's dynamics and optimal in the sense of minimum agility and time. They pass through given set of way points, guarantee flight without a side-slip, and satisfy vehicle's dynamics and actuator constraints. In addition, an algorithm is presented to compute the required power to traverse the generated trajectory. Presented algorithms are implementable in real time using on-board computers. They do not take into account the vehicle's existing flight controller, hence there is no guarantee that the controller will be able to provide acceptable tracking of the generated trajectory, especially in the presence of atmospheric disturbances. To this end, we propose an adaptive augmentation algorithm to improve vehicle's performance by taking into account the effects of disturbances and on-line estimates of vehicle's existing flight controller's gains. The algorithms have been verified by simulations using DJI S1000 octocopter's model

An Autonomous Autopilot Control System Design for Small-Scale UAVs

This paper describes the design and implementation of a fully autonomous and programmable autopilot system for small scale autonomous unmanned aerial vehicle (UAV) aircraft. This system was implemented in Reflection and has flown on the Exploration Aerial Vehicle (EAV) platform at NASA Ames Research Center, currently only as a safety backup for an experimental autopilot. The EAV and ground station are built on a component-based architecture called the Reflection Architecture. The Reflection Architecture is a prototype for a real-time embedded plug-and-play avionics system architecture which provides a transport layer for real-time communications between hardware and software components, allowing each component to focus solely on its implementation. The autopilot module described here, although developed in Reflection, contains no design elements dependent on this architecture

Intelligent Hardware-Enabled Sensor and Software Safety and Health Management for Autonomous UAS

Unmanned Aerial Systems (UAS) can only be deployed if they can effectively complete their mission and respond to failures and uncertain environmental conditions while maintaining safety with respect to other aircraft as well as humans and property on the ground. We propose to design a real-time, onboard system health management (SHM) capability to continuously monitor essential system components such as sensors, software, and hardware systems for detection and diagnosis of failures and violations of safety or performance rules during the ight of a UAS. Our approach to SHM is three-pronged, providing: (1) real-time monitoring of sensor and software signals; (2) signal analysis, preprocessing, and advanced on-the- y temporal and Bayesian probabilistic fault diagnosis; (3) an unobtrusive, lightweight, read-only, low-power hardware realization using Field Programmable Gate Arrays (FPGAs) in order to avoid overburdening limited computing resources or costly re-certi cation of ight software due to instrumentation. No currently available SHM capabilities (or combinations of currently existing SHM capabilities) come anywhere close to satisfying these three criteria yet NASA will require such intelligent, hardwareenabled sensor and software safety and health management for introducing autonomous UAS into the National Airspace System (NAS). We propose a novel approach of creating modular building blocks for combining responsive runtime monitoring of temporal logic system safety requirements with model-based diagnosis and Bayesian network-based probabilistic analysis. Our proposed research program includes both developing this novel approach and demonstrating its capabilities using the NASA Swift UAS as a demonstration platform

Cybersecurity Threat Assessment of Small Unmanned Aerial System (UAS) Aircraft Configuration

This presentation details a cybersecurity analysis and background for a small UAS configuration at NASA Ames Research Center. This presentation covers the approach devised, methodology, and results of the analysis for this configuration

Enabling UAS Research at the NASA EAV Laboratory

The Exploration Aerial Vehicles (EAV) Laboratory at NASA Ames Research Center leads research into intelligent autonomy and advanced control systems, bridging the gap between simulation and full-scale technology through flight test experimentation on unmanned sub-scale test vehicles

Real-Time Path Planning for Multi-copters flying in UTM -TCL4

NASA's UAS Traffic management (UTM) -TCL-4 focuses on safely enabling large scale small UAS oper- ations in low altitude airspace in dense urban regions. This paper presents an operational architecture of an autonomous unmanned aerial vehicle operating in TCL4. An on-line path planning scheme is proposed which can effectively plan for feasible paths in real time with TCL-4 constraints. An end to end system is designed and tested in high fidelity Reflection architecture which demonstrates the feasibility of the approach

Preliminary Assessment of Optimal Longitudinal-Mode Control for Drag Reduction through Distributed Aeroelastic Shaping

The emergence of advanced lightweight materials is resulting in a new generation of lighter, flexible, more-efficient airframes that are enabling concepts for active aeroelastic wing-shape control to achieve greater flight efficiency and increased safety margins. These elastically shaped aircraft concepts require non-traditional methods for large-scale multi-objective flight control that simultaneously seek to gain aerodynamic efficiency in terms of drag reduction while performing traditional command-tracking tasks as part of a complete guidance and navigation solution. This paper presents results from a preliminary study of a notional multi-objective control law for an aeroelastic flexible-wing aircraft controlled through distributed continuous leading and trailing edge control surface actuators. This preliminary study develops and analyzes a multi-objective control law derived from optimal linear quadratic methods on a longitudinal vehicle dynamics model with coupled aeroelastic dynamics. The controller tracks commanded attack-angle while minimizing drag and controlling wing twist and bend. This paper presents an overview of the elastic aircraft concept, outlines the coupled vehicle model, presents the preliminary control law formulation and implementation, presents results from simulation, provides analysis, and concludes by identifying possible future areas for researc